Quick answer: There is no single “Synology NAS USB boot” procedure; first identify which device needs to boot. Three situations are often confused: (1) Installing DSM on a new NAS: the NAS is the target; use Web Assistant (find.synology.com) or Synology Assistant for your model, no USB boot needed. (2) Restoring a PC or server from Active Backup for Business (ABB): the PC or server is the target; create ABB USB recovery media to boot that machine, then connect to the backup on the NAS. (3) A NAS that has failed or will not reach DSM: this is a diagnosis of power, network and drives, not a matter of creating a NAS boot USB. Always protect the data before you act.
Before you start, decide which device needs to boot and whether your goal is to install DSM, recover a computer or deal with a faulty NAS. If you are deploying a NAS for your business, see our Synology solutions; if you have lost access to data, read the NAS fault triage process before changing anything.
Three tasks that are often all called “USB boot NAS”
1. Installing DSM on a new NAS: the NAS is the target. Follow the guide for your model, find the NAS on the local network with Web Assistant or Synology Assistant and follow the on-screen status. 2. Restoring a PC or server from ABB: the PC or server is the target; the USB recovery media boots that machine into a recovery environment, which then connects to the backup on the NAS. 3. A NAS that is failing or will not start: this is a diagnostic process covering power, network, hardware, DSM and drives, not a reason to create a USB to boot the NAS.
Identify exactly which device needs to boot before you download any ISO or pick a USB drive. Record the NAS model, the DSM/ABB version, the operating system of the machine to be recovered, the time of the latest backup and the storage pool status. If the business data exists only in one copy, stop anything that could overwrite it and have the responsible person assess the risk.
If you want to install DSM on a new Synology NAS
According to Synology, the standard process starts with compatible drives installed, the NAS powered on and on the same local network as the admin computer. Open Web Assistant in a browser to find the device in its “not installed” state, or use Synology Assistant. The steps and warnings vary by model and DSM version; open the documentation for your exact model rather than using a USB boot file from a forum.
Without internet access, Synology’s documentation describes using Synology Assistant with the DSM .pat file for the correct model and version. The .pat file is loaded through the installer; it does not turn a USB drive into a NAS boot drive. Before reinstalling on a device that has held data, check backups, encryption and volume status, and do not choose to erase or initialise unless you understand the consequences.
If you want to create USB recovery media for a PC or server backed up to the NAS
First, ABB must have a completed backup task and a suitable restore point. On a compatible Windows computer, download Active Backup for Business Recovery Media Creator from Synology’s official download centre. The tool may need the Windows ADK and Windows PE, depending on current guidance. Use a dedicated USB drive and double-check the target drive, because creating the media may format it, then choose to create USB recovery media in the tool.
Afterwards, test booting the machine to be recovered from the USB in a controlled test. Check storage and network drivers, the connection to the NAS and that you can see the expected backup; do not run a restore that overwrites a working machine just to “test”. Record how to choose UEFI/BIOS boot, any encryption keys, which accounts may restore and who to contact in an incident. A backup plan is only trustworthy once the media and recovery path have been tested.
For Linux, Synology has separate documentation on recovery ISOs and USB boot for Linux machines. The disk-image commands in those documents can erase the whole selected drive; this article deliberately does not copy them, to avoid readers targeting a production disk by mistake. Use the documentation for your operating system and have a technician confirm the target device first.
If the NAS will not start or you cannot reach DSM
Start with what you can observe: the power light, beeps, LAN lights, whether the device is found on the network, when the fault began and any alerts received. Synology recommends checking power, network cables and ports, and device status according to its troubleshooting guide. Do not treat “cannot open the DSM page” as “the NAS will not boot”: DNS, network, IP or browser problems can look similar.
If there are signs of drive failure, a degraded or crashed storage pool, or data that exists in only one copy, do not swap drive positions, initialise the pool, reinstall DSM or try a reset mode you do not fully understand. Preserve the evidence, record the serial number, model and status screenshots, confirm there is an independent backup and hand over to the responsible team. Our articles on common mistakes when handling NAS faults and the loss-of-access checklist help narrow the scope before you intervene.
Checklist before you act
State the goal clearly: install a new NAS, recover a workstation from ABB, or rescue a NAS holding data. Check the model, versions, backup and restore point status, and who has authority to decide. For USB recovery, confirm which USB drive will be formatted and which machine will boot from it. For a failing NAS, record power, network and drive symptoms and stop before any initialise or overwrite operation. Businesses should keep a separate backup, a named person who receives alerts and a record of restore tests; RAID or a single USB recovery drive does not replace these steps.
Frequently asked questions
Can I install DSM on a Synology NAS with a USB boot drive?
Synology’s official DSM installation guide uses Web Assistant or Synology Assistant and the DSM file for your model when manual installation is needed. ABB USB recovery media is not a way to install DSM on a NAS.
Which device does ABB USB recovery media boot?
The computer or server that needs to be restored from the backup on the NAS. It is not a boot drive for the NAS itself.
Is creating the USB enough to be ready for recovery?
No. You also need a usable backup, compatible media, working drivers and network, the right access permissions and a test that finds the correct restore point.
Should I reset a NAS straight away if it will not reach DSM?
Not until you have checked power, network, drive status and backups. Reset modes differ in their effects; follow the documentation for your model and DSM version, or have a technician assess it first.
Technical sources
Synology: installing DSM; Synology: ABB Recovery Media Creator; Synology: unresponsive NAS. Check the documentation for your model, DSM and ABB versions. For help, contact IT Systems at hotline 028.3995.03.59 or contact@itsystems.com.vn.
Use a Synology NAS instead of a PC sharing its drive
- Synology NAS DS925+ – 4 bays, file sharing and backup for offices · VND 18,100,000
- Synology NAS DS1525+ – 5 bays, more capacity, expandable · VND 25,700,000
See Synology solutions for businesses. Prices excl. VAT, from IT Systems Store, Nov 2026.
Need someone to run your servers, NAS and systems?
IT Systems manages servers, NAS, cloud, backup and user accounts on a schedule, with a monthly operations report.




